環氧地坪的基礎該如何處理？杭州賽卡地坪工程有限公司的技術轉接周工為咱們整理了如下的方法供大家參考整理的方法

　　第一、用研磨機進行全面打磨。讓破損、起沙、粘度不牢、開裂、空鼓之部位完全暴露出來;并將浮起的砂漿、舊環氧水泥結塊等打磨平整?；炷吝M行認真打磨，不能漏掉半點不打磨的地方，特別是很多強度不好的區域，一定要打磨到有強度的地方，否則，疏松的區域會隨著涂層脫落，而且時間會很快，可能工程還沒有結算就會脫掉;同時，建議打磨進行兩道，兩次呈十字交叉型，以防止有漏點，可以打磨得更加徹底。

　　第二、用研磨機進行全面打磨。讓破損、起沙、粘度不牢、開裂、空鼓之部位完全暴露出來;并將浮起的砂漿、舊環氧水泥結塊等打磨平整。打磨結束后，清掃完后，建議用吸塵器吸塵處理，以便涂料更好地滲透，水的張力大，容易影響滲透性;

　　第三、用研磨機進行全面打磨。讓破損、起沙、粘度不牢、開裂、空鼓之部位完全暴露出來;并將浮起的砂漿、舊環氧水泥結塊等打磨平整。對于沒有伸縮縫的地面，要進行深切縫，以防止將來由于混凝土的內應力，形成不規則裂縫;有伸縮縫的地方，用鋼筋鉤進行清縫，然后用吸塵器進行吸塵。

　　第四、有不規則裂縫的地方，要進行切縫處理，用環氧砂漿進行修補，并注意修補的高低差;

　　第五、將處過的地面清潔。檢驗方法：經處理后，地坪表面平整、密實、干燥，無油污、且沒有松動易碎顆粒，方可進行下一工序施工。伸縮縫、裂縫、空鼓地面、松動舊環氧的特殊處理

　　柱邊和墻角邊用角磨機進行角磨，處理的平整、平滑;

　　第六、有水的地方用吸水器把水處理掉，鏟除表面的泥漿，然后用帶水的洗地機洗地吸水，處理干凈，晾一天，隨后上底漆;

　　第七、有油污的地方，先把表面的油垢鏟除干凈，然后用清洗劑進行清洗，然后再用火烤，如果油污特別嚴重，需要敲掉混凝土重新澆筑。

　　Basic handling method of epoxy floor for company information

　　First, use the grinding machine for comprehensive grinding. Let damage, sand, viscosity is not firm, cracking, empty drum parts completely exposed; And the floating mortar, old epoxy cement agglomeration and other grinding smooth. Concrete should be carefully polished, not to miss any place that is not polished, especially many areas with poor strength, must be polished to the place with strength, otherwise, loose area will fall off with the coating, and time will be very fast, may not have the project settlement will take off; At the same time, it is recommended to carry out two grinding, two cross type, in order to prevent leakage point, can be more thorough grinding.

　　Second, use the grinder for full grinding. Let damage, sand, viscosity is not firm, cracking, empty drum parts completely exposed; And the floating mortar, old epoxy cement agglomeration and other grinding smooth. After the end of grinding, cleaning, it is recommended to vacuum treatment, so that the paint better penetration, water tension, easy to affect the permeability;

　　Third, the use of grinding machine for comprehensive grinding. Let damage, sand, viscosity is not firm, cracking, empty drum parts completely exposed; And the floating mortar, old epoxy cement agglomeration and other grinding smooth. For the ground without expansion joints, deep joints should be carried out to prevent irregular cracks caused by the internal stress of concrete in the future. The place that has telescopic seam, undertake clear seam with rebar hook, have vacuum cleaner next.

　　Fourth, where there are irregular cracks, it is necessary to conduct slit treatment, repair with epoxy mortar, and pay attention to the difference between the high and low repair;

　　Fifth, the floor will be clean. Inspection method: after the treatment, the floor surface is flat, dense, dry, no oil, and no loose fragile particles, before the next process of construction. Special treatment of expansion joints, cracks, empty drum floor and loose old epoxy

　　Column edge and corner edge Angle grinding machine Angle grinding, processing of the smooth, smooth;

　　Sixth, where there is water, use a water absorber to treat the water, remove the mud on the surface, and then wash the ground with water to absorb water, clean treatment, drying for a day, then on the primer;

　　Seventh, where there is oil pollution, first the surface of the oil scale to eliminate clean, and then use cleaning agent for cleaning, and then use fire to bake, if the oil pollution is particularly serious, need to knock off the concrete pouring.